sum 1/8 low frequency power amplifier general description outline drawing CD8227GP is audio power ic with built-in two channels developed for portable radio cassette tape recorder with power on/off switch. thermal shut down protection circuit is built in. because of the parts reduction and dip (dual in line package), space merit is remarkable. features z high power pout=2.5w/ch(typ.) :(vcc=9v,r l =4 ? ,f=1khz,thd=10%) pout=3.0w/ch(typ.) :(vcc=9v,r l =3 ? ,f=1khz,thd=10%) z voltage gain: gv=45db(typ.) ? rf=120 |? ,f=1khz ? gv=56.5db(typ.) ? rf=0 |? ,f=1khz z low popping noise at power on z small quiescent current : i ccq =21ma(typ.) (vcc=9v vin=0) z ripple rejection ratio : r.r.=-52db(typ.)(vcc=9v ? fripple=100hz ? rg=600 |? ) z cross talk : c.t .= -50db(typ.)(vcc=9v ? f=1khz ? rg=600 |? ) z output noise voltage : vno=0.3mvrms(typ.)(vcc=9v ? rg=10k |?? bw=20hz~20khz) z stand-by switch z soft clip z built-in thermal shut down protection circuit z best for supply voltage 9v z s upply voltage range : vcc=5~12v sum CD8227GP http://www..net/ datasheet pdf - http://www..net/
sum CD8227GP sum 2/8 maximum ratings (ta=25 c) characteristic symbol rating unit output current (peak/ch) i q(peak) 1.50 a power dissipation* p d 3.00 w operating temperature topr -25~75 c storage temperature tstg -55~150 c * value for mounting on pc board(refer to p d -ta curve) electrical characteristics (unless otherwise specified , vcc=9v,f=1khz, rg=600 ? , r l =4 ? ,ta=25c) characteristic symbol test condition min. typ. max. unit quiescent current i ccq v in =0 - 21 45 ma p out(1) thd=10% 2.0 2.5 - output power p out(2) thd=10%, r l =3 |? - 3.0 - w total harmonic distortion thd p out =0.4w/ch - 0.2 1.0 % g v(1) rf=120 |? v out =0dbm 43 45 47 voltage gain g v(2) rf=0,v out =0dbm - 56.5 - db input resistance r in - - 30 - k |? output noise voltage v no rg=10k |? , bw=20hz~20khz - 0.3 1.0 mv rms ripple rejection ratio r.r rg=600 |? , fripple =100hz - -52 - db cross talk c.t rg=600 |? , v out =0dbm, - -50 - db input offset voltage v6,v7 - - 30 60 mv stand-by current istb sw1-off 1 | a typical dc voltage of each terminal (vcc=9v,ta=25 c) terminal no. 1 2 3 4 5 6 7 8 9 10 11 12 dc voltage (v) vcc 4.5 8.7 gnd 0.7 0.03 0.03 0.7 5.0 8.7 4.5 vcc http://www..net/ datasheet pdf - http://www..net/
sum CD8227GP sum 3/8 test circuit & block diagram *(1) this ic can be used without coupling capac itor (cin),if volume slide noise occurred by input offset voltage is undesirable, it needs to use the capacitor(cin). *(2) the condenser between the pin and the gnd(c11)is for reducing pop noise when the power on/off switch (sw1)is set to on/off. application information and application method 1. adjustment of voltage gain the voltage gain gv is obtained as follows by r1,r2 and rf in fig.1. gv=20log((rf+r1+r2)/(rf+r1)) when rf=0 gv=56.5db(typ.) when rf=120 ? gv=45db(typ.) by increasing rf , reduction of gv is possible , however, since the feedback fig 1. increase is liable to produce oscillation , it is recommended to use this at 40db or over. http://www..net/ datasheet pdf - http://www..net/
sum CD8227GP sum 4/8 2. thermal shut-down circuit the thermal shut-down circuit is bui lt in for the purpose of preventing the destruction of ic due to the abnormal temp erature rise when the heat radiation is insufficient. the operation temperature is set at ra diation fin temperature 175c(typ.) at this temperature or over the bias is interrupted to prevent the destruction of ic. 3. input stage the input circuit of this ic is as shown in fig.2. pnp tr: q1 is provided in the input circuit so as to make its usage possible without the input coupling capacitor. however , at pins t and ? ,max 60mv offset voltage is produced. application after checking volume slide noise is recommended. for cutting the volume slide noise, insert the input capacitor: c in in series to interrupt the dc component fig.2 4. oscilation preventive measures for oscillation preventive cap acitor c6 and c7 between th e output terminal and gnd, it is recommended to use polyester film ca pacitor having good characteristics for temperature and for high frequency. since the characteristics of the capacitor is liable to be influenced by the temperature, use this capacitor after the temperature test to check the oscillation allowance. in addition, as the position of the electrolytic capacitor has a remarkable influence on the oscillation ,connect c10 to vcc at the nearest possible position from power gnd. at using this application with the voltage gain reduced, oscillation is liable to be produced. apply the capacitor after checki ng enough for its capacity, type and mounting position. http://www..net/ datasheet pdf - http://www..net/
sum CD8227GP sum 5/8 as the oscillation allowance varies acc ording to the printed pattern layout, the standard printed board is recommended to be referred to des ign it 5. input voltage when the excessive signal is input, turning-up is produced in the clip waveform. the turning-up point is v in =300mvrms(typ.) : vcc=9v, r l =4 ? , f=1khz : enough care must be taken for this phenomenon. 6. power on/off switch there is power on/off switch at pin 1. however, output power is changed by pin 1 supply voltage when pin 1 voltage in not same pin 12 supply voltage, after referring to attached date, select pin 1 supply voltage. 7. gnd line gnd pin is not separated for pre-gnd a nd for pw-gnd. that is liable to cause distortion and cross talk worse. before use this ic, please check it. characteristic curves http://www..net/ datasheet pdf - http://www..net/
sum CD8227GP sum 6/8 http://www..net/ datasheet pdf - http://www..net/
sum CD8227GP sum 7/8 http://www..net/ datasheet pdf - http://www..net/
sum CD8227GP sum 8/8 http://www..net/ datasheet pdf - http://www..net/
|
